Sonic Alert SBD375SS-V3 Clock Radio user manual

Sonic Boom Dual Alarm Clock with Bed Shaker

Model SBD375ss-v3

OPERATION INSTRUCTIONS

IMPORTANT Please read these instructions carefully before use and retain for future reference. See operating instructions on back.

Use only the supplied or recomended Sonic Alert adaptor to connect the

Warning: To prevent fire or shock hazard do not expose this appliance to rain or moisture. Before connecting to mains/ power make sure that the requirements specified on the apparatus corresponds to the available power

The ventilation should not be impeded by covering the ventilation openings with items such as, newspaper, table cloth, curtains, etc;

No naked flame sources, such as lighted candles should be placed on the apparatus.

It shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Do not place the product in closed bookcases or racks without proper ventilation.

Where the mains/ power plug is used as the disconnect device, the disconnect device shall remain readily operable.

OPERATION INSTRUCTIONS

Features shown on diagram above:

1) Alarm Selector

2) Vibrator Hi/Lo Switch

3) Clock Display

4) PM Indicator

5) Alarm SET/ OFF Button / Alarm

Duration Time

6) Fast Min./ Hour Button / 12 or 24

Hour Selector

7) Slow Min./ Hour Button

8) Snooze Button/ Snooze Duration

Time/ Dimmer Control

9) Time Set Switch

10) Tone Control Wheel

11) Alarm Mode Switch

12) Alarm-1 Indicator (AL1)

13) Alarm-2 Indicator (AL2)

14) Volume Control Wheel

15) Vibrator / Bed Shaker Input

16) DC Power Input

17) Backup Battery Compartment

Test Mode:

1) Press and hold the Snooze and Time buttons for 3 seconds to enter the Test

Mode. The display will show "7ES7" to indicate it is in TEST Mode.

2) If within 1 minute no button is pressed, then it will exit the Test Mode and return back to the Time Mode.

3) Press any button within 1 minute (except the Snooze & Time buttons, which has no effect), it will exit the Test Mode immediately.

4) While in Test Mode, sliding the Function Switch will demonstrate the different functions of the clock: a) Function Switch at OFF, it will have a continuous "Vee" sound to indicate it is in the Test Mode. b) Function Switch at BUZZ, it will demonstrate the buzzer sound. c) Function Switch at VIB, it will demonstrate the vibrator. d) Function Switch at VIB & BUZZ, it will demonstrate the buzzer sound & the

5) After finish with the Test Mode, press any button (except the Snooze & Time buttons, which has no effect) it will exit the Test Mode immediately.

Setting the Correct Time

1) Press and hold the TIME Button (9) and at the same time press the FAST Button (6) or the SLOW button (7) to advance clock display unil you have desired time.

2) The lighted dot (4) located in upper left corner of the clock display indicates the time is

PM. For AM time, this dot will not light up.

Setting the Alarm Time

Setting Alarm 1

1) Slide the ALARM SELECTOR (1) to AL1 position, the alarm indicator AL1 (12) will

2) Press and hold the ALARM SET /OFF (5) button and at the same time press the

FAST Button (6) or the SLOW button (7) to advance clock display until you reach desired alarm setting.

3) Make sure alarm time is correctly set for AM or PM (4).

Setting Alarm 2

4) Once alarm AL1 has been set, slide ALARM SELECTOR (1) to AL2 position. , the alarm indicator AL2 (13) will light up.

5) Slide the ALARM SELECTOR (1) to AL2 position, the alarm indicator AL2 (13) will

6) Press and hold the ALARM SET /OFF (5) button and at the same time press the

FAST Button (6) or the SLOW button (7) to advance clock display until you reach desired alarm setting.

Selecting 12 or 24 hours format Clock is set to 12 hour as the default setting

Press and hold the Fast Button (9) for 6 seconds to enter the hour selection mode, release the Fast Button (9) when the display shows "12 H" or "24 H". Press and release the hour button to toggle between 12 or 24 hours. If no selection is made within 4 seconds, then the last displayed hour format will be chosen and the display will return to the normal

Time mode.

Enable Alarms:

1) To enable Alarm 1, slide the ALARM SELECTOR (1) to AL1 position. the alarm indicator AL1 (12) will light up.

2) To enable Alarm 2, slide the ALARM SELECTOR (1) to AL2 position, the alarm indicator AL2 (13) will light up.

3) To enable both alarms, slide the ALARM SELECTOR (1) to AL2 position, the alarm indicators AL1 (12) and AL2 (13) will light up.

To Select Wake up mode

To select the wake up mode, slide the Alarm Mode Switch (11) to your desired position:a) BUZZ for sound b) VIB for bed shaker c) VIB/ BUZZ for both sound and bed

NOTE: once the wake up mode is chos