Marlin 07' Clock User Manual

The RoadKingFlip Fork Lock Cover Clock or Thermometer takes the place of the factory installed fork lock plate. The RKF comes with either a clock or thermometer, one extra rubber compression ring, two screws, one clear plastic spacer, one battery replacement tool and billet mount.

1) Carefully remove the item from its package.

2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or similar object in a screwdriver style motion or use the Pull Here tab if so equipped, you may also be able to push through the hole in the bottom of the holder. Make sure that the clock does not fall and become damaged.

3) Carefully pry off factory plastic fork lock plate that has Unlock-Lock on it.

4) Then remove the two Phillips screws beneath the lock plate.

5) Open the mount by pulling the top half up from the base, place the mount and the clear rubber spacer that goes under the mount in position over the two exposed screw holes.

6) Apply LOCTITE242 blue to the thread of the screws provided and install the screws to hold the cover in place. (The LOCTITEprevents loosening of threaded fasteners.)

7) The Fork Lock Cover spring closes cover automatically. (The cover WILL NOT stay open)

8) After setting the time per instructions on bag, install the clock into the holder/mount all the way as per instructions on in the General Care section of these instructions.

NO KEY MODIFICATION IS REQUIRED FOR RKF

Roadking- All models 94-07

Roadking- All models 94-07

The Road King Swivel Fork Lock Cover Clock or Thermometer takes the place of the factory installed fork lock plate. The RKS comes with either a clock or thermometer, one extra rubber compression ring, two screws, one clear plastic spacer, one battery replacement tool and billet mount.

1) Carefully remove the item from its package.

2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or similar object in a screwdriver style motion or use the Pull Here tab if so equipped, you may also be able to push through the hole in the bottom of the holder. Make sure that the clock does not fall and become damaged.

3) Carefully pry off factory plastic fork lock plate that has Unlock-Lock on it.

4) Then remove the two Phillips screws beneath the lock plate.

5) Open the mount by rotating the top half clockwise, place the mount and the clear rubber spacer that goes under the mount in position over the two exposed screw holes.

6) Apply LOCTITE242 blue to the thread of the screws provided and install the screws to hold the cover in place.

(The LOCTITEprevents loosening of threaded fasteners.)

7) The Fork Lock Cover turns counterclockwise to close.

8) After setting the time per instructions on bag, install the clock into the holder/mount all the way as per instructions in the General Care section of these instructions.

9) Your will need to modify your key. The blade of the key will hit the head of the clock mount. You need to grind one edge of your key as shown in the photo. If you feel that you do not want cut your original key, purchase a spare key from your Harley Davidson. Dealer. They come in pairs.

BBCS2 Most 7/8-1-1 1/4 Bars

Please contact Marlins for service before returning item to dealer

The Brake/Clutch Mount Clock or Thermometer fits onto your brake or clutch control unit using the existing mounting bolt. It may also be affixed to a windshield horizontally and then adjusted up or down for better viewing.

The Brake/ClutchMount comes with either a clock or thermometer, one extra rubber compression ring, one hex head wrench, one battery replacement tool and billet mount.

1) Carefully remove the item from its package.

2) To remove the clock pry slowly under the edge of the clock with the long flat side of a knife or similar object in a screwdriver style motion or use the Pull Here tab if so equipped. Make sure that the clock does not fall and become damaged.

3) For control unit installation remove one bolt from the top or bottom of the handlebar control clamp.

4) Place the mount in position and re-insert the bolt and tighten.

5) Loosen the hex screw on the head unit, move it into position desired and tighten hex screw to lock head in place.

6) After setting the time per instructions on bag, install the clock into the holder/mount all the way as per instructions in the General Care section of these instructions.

The Brake/Clutch Mount Clock and Thermometer fits onto your brake or clutch control unit using the existing mounting bolt. It may also be affixed to a windshield horizontally and adjusted up or down for better viewing.

The Brake/ClutchMount comes with both a clock and thermometer, two extra rubber compression rings, one hex head wrench, one