Makita 6303 Drill user manual

13 mm (1/2") MODEL 6302

Variable speed / Reversing

13 mm (1/2") MODEL 6303

Variable speed / Reversing

INSTRUCTION MANUAL

INSULATION

SPECIFICATIONS

13 mm (112")

3 6 mm (1-318")

285 mm (1 1-114")

2.0 kg (4.4 Ibsl

13 mm (1/2")

3 6 mm (1-3/8"1

285 mm (11-114")

2.0 kg (4.4 Ibsl

IMPORTANT

SAFETY INSTRUCTIONS

(For All Tools)

WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO

REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS.

1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.

2. CONSIDER WORK AREA ENVIRONMENT. Dont use power tools in damp or wet locations. Keep work area well lit. Dont expose power tools t o rain.

Dont use tool in presence of flammable liquids or gases.

3. KEEP CHILDREN AWAY. All visitors should be kept away from work area.

Dont let visitors contact tool or extension cord. or locked-up place out of reach of children.

5. DONT FORCE TOOL. It will do the job better and safer at the rate for which it was intended. heavy-duty tool. Dont use tool for purpose not intended.

7 . DRESS PROPERLY. Dont wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and nonskid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

USE SAFETY GLASSES. Also use face or dust mask if cutting operation is

9. DONT ABUSE CORD. Never carry tool by cord or yank it t o disconnect from receptacle. Keep cord from heat, oil, and sharp edges.

IO. SECURE WORK.

Use clamps or a vise t o hold work. Its safer than using your hand and it frees both hands t o operate tool.

11. DONT OVERREACH. Keep proper footing and balance at all times.

12. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.

13. DISCONNECT TOOLS. When not in use, before servicing, and when changing accessories, such as blades, bits, cutters.

14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning

15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.

16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked.

17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are tired.

18. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked t o determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual.

Have defective switches replaced by authorized service center. Don't use tool if switch does not turn it on and off.

19. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures.

20. REPLACEMENT PARTS. When servicing, use only identical replacement parts.

21. POLARIZED PLUGS: To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user - as well as damage t o the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful t o the motor.

ADDITIONAL SAFETY RULES

1. Always be sure you have a firm footing.

Be sure no one is below when using the tool in high locations.

2. Hold the tool firmly.

3. Keep hands away from rotating parts.

4. When drilling into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL