DeWalt D25501 Power Hammer user manual

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUAL DE INSTRUES

INSTRUCTIVO DE OPERACIN, CENTROS DE SERVICIO Y PLIZA DE

GARANTA. ADVERTENCIA: LASE ESTE INSTRUCTIVO ANTES DE USAR

EL PRODUCTO.

INSTRUES DE OPERAO, CENTRO DE SERVIOS E CERTIFICADO

DE GARANTIA. ADVERTNCIA: LEIA ESTAS INSTRUES ANTES DE

UTILIZAR O PRODUTO.

1-9/16" (40 mm) SDS Max Hammers / Martillo de 1-9/16" (40 mm) SDS Max / Martelo 1-9/16" (40mm) SDS Max

1-3/4" (45 mm) SDS Max Demolition Hammer / Martillo Demoledor de 1-3/4" (45 mm) SDS Max / Martelo Demolidor

1-3/4" (45 mm) SDS Max

1-3/4" (45 mm) SDS Max Hammers / Martillo de 1-3/4" (45 mm) SDS Max / Martelo 1-3/4" (45 mm) SDS Max

D25831, D25851

SDS Max and Spline Chipping Hammers / Martillos de burilado SDS Max y estriados / Marteletes de raspagem de ranhura e SDS Max

c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Definitions: Safety Guidelines

2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply.

Use of a GFCI reduces the risk of electric shock.

WARNING: To reduce the risk of injury, read the instruction

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term power tool" in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-

1) WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc., in accordance with these instructions taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could result in a hazardous situation.